-17%

Hp-Z240-CORE-I7-7TH-GEN-8GB RAM-1TB-HDD-2GB GPU


Brand: hp
Model: z240
Processor Type: core i7 7th gen
Memory: 8GB ddr4
Hdd: 1TB
Graphic card: 2GB

KSh29,000.00 KSh35,000.00 (ex-VAT)

System board

Specification
Description
System board form factor
ATX 24.89 x 24.38 mm (9.8 x 9.6 in)
Processor socket
Single LGA 1151
CPU bus speed
DMI
Memory expansion slots
4 DDR4 memory slots
Memory type supported
DDR4, UDIMM (unbuffered), ECC and non-ECC
Memory modes
Non-interleaved for single channel. Interleaved when both channels are populated.
Memory speed supported
2133MT/s DDR4
Memory protection
ECC available on data
Maximum memory
64 GB
Memory configuration
4GB, 8GB and 16GB non-ECC/4GB, 8GB and 16GB ECC unbuffered DIMMs are supported. ECC and non-ECC memory DIMMs cannot be mixed on the same system.
PCI express connectors
1 PCI Express Gen3 slot x 1 mechanical/ x 1 electrical (full height, full length)
1 PCI Express Gen3 slot x 16 mechanical/ x 16 electrical (full height, full length)
1 PCI Express Gen3 slot x 4 mechanical/ x 4 electrical (full height, full length)
1 PCI Express Gen3 slot x 16 mechanical/ x 4 electrical (full height, full length)

NOTE:

In the PCIe Gen3 (x 16 electrical/x 16 mechanical) slot, if it is not being used for a graphics card, only cards certified as After Market Options for this platform are supported.
PCI connectors (5 V)
1 (optional) PCI slot, full height, full length
Supported drive interfaces
SATA:
Integrated (4) Serial ATA interfaces (6 Gb/s SATA). One port can optionally be used for eSATA. RAID 0 and 1 supported. Factory integrated RAID is Microsoft Windows only. RAID 5 is supported by Software XOR.
Serial Attached SCSI
None
Integrated RAID:

NOTE:

Requires identical hard drives (speeds, capacity, interface)
Integrated graphics:
Intel HD Graphics 530 (on Core i3/i5/i7-6xxx processors); Intel Integrated Graphics for Xeon processors
Based on Unified Memory Architecture (UMA) – a region of system memory is reserved and dedicated to the graphics display.
Support for Mic1 DVI-D and 2 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP and DVI-D outputs.
1 DVI-D and 2 DP 1.2 graphics ports integrated in motherboard; Supports up to three simultaneous displays across DP and DVI-D outputs.
Maximum resolution supported on DVI- D ports: 1920 x 1200 at 60Hz
Maximum resolution supported on DP 1.2 ports: 3840×2160 at 60Hz
Network controller:
Integrated Ethernet PHY Connection I219LM. Management capabilities: WOL, PXE 2.1 and AMT 9
External SATA (eSATA):
External SATA (eSATA): 1 port eSATA capable (SATA 3) with optional eSATA after-market option cable kit
IDE connector:
No
Floppy connector:
No
Serial:
1 internal header (requires optional serial port adapter kit)
2nd Serial:
No
Parallel:
1 internal header (optional parallel port adapter required)
HD integrated audio:
Yes
USB connectors
Front: 2 USB 3.0, 1 USB 2.0, 1 USB 2.0 charging data port
Rear: 4 USB 3.0, 2 USB 2.0
Internal: 1 USB 3.0 and 3 USB 2.0 ports available as 2 separate 2 x 6 (3.0 x 1.2.0 x 1) and 1 x 6 (2.0 x 1) headers: supports 1 HP Internal USB port kits plus one USB 3.0 SD card reader
HD integrated audio
Yes
Flash ROM
Yes
CPU fan header
Yes
Chassis fan header
1 rear system chassis fan header
Front control panel/speaker header
Yes
CMOS battery holder – lithium
Yes
Integrated trusted platform module
Integrated TPM 1.2
The TPM module disabled where restricted by law, i.e. Russia
Power supply headers
Yes
Power switch, power LED and hard drive LED header
Yes
Clear password jumper
Yes
Keyboard/mouse
USB or PS/2
Operating voltage range
90-269 VAC
Maximum: 890 btu/hr (224 kcal/hr)
Rated voltage range
100-240 VAC
Rated line frequency
50-60 Hz
Operating line frequency range
47-66 Hz
Rated input current
6A at 100-240 V
Heat dissipation
Typical: 444 btu/hr (112 kcal/hr)
Maximum: 1484 btu/hr (374 kcal/hr)
Power supply fan
80 x 80 x 25 mm (3.1 x 3.1 x 0.98 in) 4-wire PWM
ENERGY STAR qualified (config dependent)
Yes
CECP compliant at 220V
Yes
FEMP standby power compliant
Yes, with wake-on-LAN disabled: < 2 W in 55 – power off
Built-in self test (BIST) LED
Yes
Surge tolerant full ranging power supply (withstands power surges up to 2000 V)
Yes
Hood lock header
Yes
ErP Lot 6- Tier 1 compliance at 230 V
Yes
ErP Lot 6- Tier 2 compliance at 230 V
Yes
Environmental requirements
Temperature:
Operating: 5° to 35° C (40° to 95° F)
Non-operating: -40° to 60° C (-40° to 140° F)
Humidity:
Operating: 10% to 90% (non-condensing)
Non-operating: 5% to 95%, 38.7° C (101.6° F) maximum wet bulb temperature
Maximum altitude:
Operating: 3,000 m (10,000 ft)
Non-operating: 9,100 m (30,000 ft)
Dynamic
Operating: 40 g, 2-3 ms, half-sine
Non-operating: 160 cm/s, 2-3 ms, half-sine. Square: 422 cm/s, 20 g
Vibration:
Operating random: 0.5g (rms), 5-300 Hz
Non-operating random: 2.0g (rms), 10-500 Hz
Cooling
Above 1524 m (5,000 ft) altitude, maximum operating temperature is de-rated by 1.8° F (1° C) per 305 m (1000 ft) elevation increase.

Physical security and serviceability

Specification
Description
Access panel
Tool-less, except for the processor heatsink.
Optical drive
Tool-less
Hard drives
Tool-less
Expansion cards
Tool-less
Processor socket
Tool-less, except for the processor heatsink
Green user touch points
Yes, on tool-less internal chassis mechanisms
Color-coordinated cables and connectors
Yes
Memory
Tool-less
System board
Screw-in
Dual color power and HD LED on front of computer
Yes
Configuration record SW
Yes
Over-temp warning on screen
Yes
Restore CD/DVD set
Consists of an operating system DVD (OSDVD) and a driver DVD (DRDVD). OSDVD restores the original operating system. DRDVD will provide all drivers for the system. The DRDVD may also contain applications that originally shipped with the system for optional installation. Applications can also be obtained from HP.com. OSDVD and DRDVD are orderable with the system and available from HP Support.
Dual function front power switch
Yes, causes a fail-safe power off when held for 4 seconds
Padlock support
Yes (optional): locks side cover and secures chassis from theft
0.22 in diameter padlock loop at rear of system
Cable lock support
Yes, Kensington Cable Lock (optional): Locks side cover and secures chassis from theft 3 mm x 7 mm slot at rear of system
Universal chassis clamp lock support
Yes (optional): Locks side cover and locks cables to chassis. Secures chassis from theft and allows multiple units to be chained together when used with optional cable Threaded feature at rear of system
Solenoid lock and hood sensor
Yes (optional)
The Solenoid Hood Lock eliminates the need for a physical key by making the chassis lockable through software and a password. You can also lock and unlock the chassis remotely over the network. The sensor kit detects when the access panel has been removed.
Rear port control cover
Yes, locks rear IO cables to prevent cable theft
Serial, parallel, USB, audio, network, enable/disable port control
Yes, enables or disables serial, USB, audio, and network ports
Removable media write/boot control
Yes, prevents ability to boot from removable media on supported devices (and can disable writes to media)
Power-on password
Yes, prevents an unauthorized person from booting up the workstation
Setup password
Yes, prevents an unauthorized person from changing the workstation configuration
3.3 V aux power LED on system PCA
Yes
NIC LEDs (integrated) (green and amber)
Yes
CPUs and heatsinks
A T-15 Torx or flat blade screwdriver is needed to remove the CPU heatsink before the CPU can be removed. CPU removal is tool-less
Power supply diagnostic LED
Yes
Front power button
Yes, ACPI multi-function
Front power LED
Yes
Front hard drive activity LED
Yes, white
Front ODD activity LED
Yes
Internal speaker
Yes
System/emergency ROM flash recovery
Recovers corrupted system BIOS.
Cooling solutions
92 x 92 x 25 mm 4-wire PWM (non-serviceable)
Power supply fans
92 x 92 x 25 mm 4-wire PWM (non-serviceable)
CPU heatsink fan
Mainstream (<= 65 W; 92 mm x 92 mm x 52.5 mm
Chassis fan
No
Memory heatsink fan
Advanced Configuration and Power Management Interface (ACPI). Allows the system to wake from a low power mode and controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system
HP PC hardware diagnostics UEFI
HP PC Hardware Diagnostics (UEFI) enables hardware level testing outside the operating system on many components. The diagnostics can be invoked by pressing F2 at POST, and is available as a download from HP Support.
Access panel key lock
No
ACPI-ready hardware
Advanced Configuration and Power Management Interface (ACPI):
Allows the system to wake from a low power mode.
Controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system.
Integrated chassis handles
Rear recessed handle; optional optical bay front handle available.
Power supply
Requires T15 Torx or flat blade screwdriver
PCI card retention
Yes, rear (all), middle (optional), front (full-length cards with extender)
Flash ROM
Yes
Diagnostic power switch LED on board
Yes
Clear password jumper
Yes
Clear CMOS button
Yes
DIMM connectors
Yes
Category: